Flash Extractor
© Soft-Center
About     Shop     Downloads     Manual     Library     Forum     Services     Contacts
RR manual updated   Search  Register  Log in
Reply to topic
Author Message
Сергей



Joined: 26 Aug 2005
Posts: 18299

Flash-Extractor developer

PostPosted: Tue Jul 21, 2020 23:13    Post subject: RR manual updated
Reply with quote

Important for Hynix RR codes

http://flash-extractor.com/manual/read_retry/

Please, update your FE and NR to last versions
Because, old versions Hynix RR can give green ECC map with wrong data
pcimage



Joined: 03 Mar 2008
Posts: 1671
Location: UK

PostPosted: Wed Jul 29, 2020 21:49    Post subject:
Reply with quote

Thank you, very helpful Smile
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Thu Sep 24, 2020 18:50    Post subject: Re: RR manual updated
Reply with quote

From manual
Quote:
Disconnect / Connect Reader
FE will ask to do it
Please, do it every time he ask

How important is it to Disconnect / Connect the reader? I wondering because when working remotely, it is not possible to do this. Should it be completely avoided?
HaQue



Joined: 16 Feb 2013
Posts: 466
Location: Adelaide, Australia

PostPosted: Thu Sep 24, 2020 19:14    Post subject:
Reply with quote

theoretically you could get around it by using Device Manager to either uninstall the USB Root Hub, then re-installing it

or disabling the re-enabling the USB mass storage device.

But not ideal for sure.
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Thu Sep 24, 2020 19:30    Post subject:
Reply with quote

I don't know the reason for the requirement to disconnect / connect it. Some registers in the reader maybe needs to be reset with a full pwr off/on ?

If that is the case, we could use a hardware switch that could be remotely controlled.
Сергей



Joined: 26 Aug 2005
Posts: 18299

Flash-Extractor developer

PostPosted: Fri Sep 25, 2020 2:10    Post subject:
Reply with quote

Memory chip do not restore RR registers values to default state after software reset

Only after power off / on

You can use Power adapter v3. It turn power off after each read
But Find Base and Tune will work much slower. Because it send additional information about voltage
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Fri Sep 25, 2020 10:51    Post subject:
Reply with quote

Сергей wrote:
Memory chip do not restore RR registers values to default state after software reset

Only after power off / on

You can use Power adapter v3. It turn power off after each read
But Find Base and Tune will work much slower. Because it send additional information about voltage

I do not have the power adapter v3 yet. Will it be enough if i make an electronic switch for Vcc on the TSOP-48 adapter board and control power off/on for the chip this way?
Сергей



Joined: 26 Aug 2005
Posts: 18299

Flash-Extractor developer

PostPosted: Fri Sep 25, 2020 19:10    Post subject:
Reply with quote

This is bad idea

1. Can burn chip
2. Chip will take power from data lines

Can try make switch at USB cable
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Sat Sep 26, 2020 11:49    Post subject:
Reply with quote

Сергей wrote:
1. Can burn chip
2. Chip will take power from data lines

Is this so even when reader is idle, not reading?

Anyhow, I will make something at the USB-cable instead.
Сергей



Joined: 26 Aug 2005
Posts: 18299

Flash-Extractor developer

PostPosted: Sat Sep 26, 2020 23:24    Post subject:
Reply with quote

Arthur wrote:
Is this so even when reader is idle, not reading?

Yes

Arthur wrote:
Anyhow, I will make something at the USB-cable instead.

I never try do it

May be need disconnect not only 5v, but also D+, D-
GND can always be connected
HaQue



Joined: 16 Feb 2013
Posts: 466
Location: Adelaide, Australia

PostPosted: Sun Sep 27, 2020 12:54    Post subject:
Reply with quote

maybe an Arduino could do it, put all 4 lines each into a switch, and use the arduino to control it
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Wed Sep 30, 2020 12:39    Post subject:
Reply with quote

HaQue wrote:
maybe an Arduino could do it, put all 4 lines each into a switch, and use the arduino to control it

Thanks. It could be done that way, or with some other simple mcu. Let's see what the solution is going to be ..

I will also order the power adapter when it becomes available again.
DiskTuna



Joined: 10 Dec 2020
Posts: 1


PostPosted: Fri Jan 08, 2021 20:03    Post subject: Re: RR manual updated
Reply with quote

Arthur wrote:
From manual
Quote:
Disconnect / Connect Reader
FE will ask to do it
Please, do it every time he ask

How important is it to Disconnect / Connect the reader? I wondering because when working remotely, it is not possible to do this. Should it be completely avoided?


Maybe one of those can be of use: https://www.yepkit.com/product/300115/YKUSHXS
pclab



Joined: 09 Jan 2021
Posts: 15


PostPosted: Sun Jan 10, 2021 14:41    Post subject: USB Voltage Regulator
Reply with quote

Can something like this also work like the voltage regulator?

https://www.gmelectronic.com/usb-regulator-module-led-display
Arthur



Joined: 17 Oct 2007
Posts: 301


PostPosted: Mon Jan 11, 2021 15:14    Post subject: Re: RR manual updated
Reply with quote

DiskTuna wrote:

Maybe one of those can be of use: https://www.yepkit.com/product/300115/YKUSHXS


Yes i have tested that one for a long time now. It works perfectly!
Display posts from previous:   
Reply to topic All times are GMT + 4 Hours
Page 1 of 1

 

Last added
CBM2099   b5 64 64 54   1x1 DM8261   45 de 94 82   1x1 OTI002168-G   ec d3 51 95   1x2 SM3267L-AE   45 3c 98 b3   1x1 SSS6696   98 de 98 92   2x2 PS5005-10   98 3a a4 93   4x2 Monolith Micro SD_24   ad 5c 28 2a   1x1 Monolith Micro SD_24   ec d7 94 7a   1x4 20-82-00469-2   45 48 9a b3   4x1 PS2251-08-Q   98 3c 99 a3   1x8
News
20.01.2021 VT can work with NTFS
29.11.2020 Find Saddle
21.07.2020 RR manual updated
10.07.2020 Power adapter in stock
05.05.2020 RR even and odd blocks
Other products
© Soft-Center ltd.